This is lastest version CCNA2 Final (Update 27-09-2009)...
(From a member have sent to quocvuong.it@gmail.com)
Download
CCNA2 Final H (Question only... i will try to answer later)
This is lastest version CCNA2 Final (Update 27-09-2009)...
(From a member have sent to quocvuong.it@gmail.com)
Download
Subscribe to:
Post Comments (Atom)
18 comment:
waiting for answer from quocvuong
Thank you very match for everything!
I passed CCNA 2 in july, and I used tests from your blog!
The new tests, I send to my friends ! They study CCNA2 with me!
I hope that I will study CCNA3 in Octomber!
Best regards from Bulgaria!
I am taking the exam tomorrow. I've been trying to answer all these questions. I already have the following answers. Could you check them, please? I'll prepare the rest of them tomorrow.
1. Refer to the exhibit. A technician has configured the interfaces on the Router, but upon inspection discovers that interface FastEthernet0/1 is not functioning. Which action will most likely correct the problem with FastEthernet0/1?
The no shutdown command needs to be added to the interface configuration.
2. Refer to the exhibit. Which route will be removed from the routing table if manual EIGRP summarization is disabled the Serial0/0/0 interface of R3?
172.16.0.0/16
4. You have been asked to explain converged networks to a trainee. How would you accurately describe a converged network?
A network is converged after all routers share the same information, calculate best paths, and update their routing tables.
5. A router that is using RIPv2 learns of the network 10.10.10.0/24 from two different neighbors. Which value is used by RIPv2 to select the best path to the network?
route metric
6. Refer to the exhibit. When the show cdp neighbors command is issued from router C, which devices will be displayed in the output?
B, D
7. In a complex lab test environment, a router has discovered four paths to 192.168.1.0/24 via the use of the RIP routing process. Which route will be installed in the routing table after the discovery of all four paths?
R 192.168.1.0/24 [120/1] via 192.168.100.1, 00:00:17, Serial0/0/1
8. Which phase of the router boot process involves running diagnostics on the hardware components from ROM?
performing the POST
9. How will a router that is configured with a classless routing protocol determine the subnet mask that should be assigned to routes that are learned from neighboring classless routers?
The subnet mask that is included in the routing updates will be used.
10. Refer to the exhibit. Which combination of IP address and subnet mask can be used on the serial interface of Router2 in order to put the interface in the same network as the serial interface of Router1?
IP 172.16.32.18, subnet mask 255.255.255.252
12. Refer to the exhibit. Both routers are using the RIPv2 routing protocol and static routes are undefined. R1 can ping 192.168.2.1 and 10.1.1.2, but is unable to ping 192.168.4.1.
What is the reason for the ping failure?
The 192.168.4.0 network is not included in the RIP configuration of R2.
13. What command would the network administrator apply to a router that is running OSPF to advertise the entire range of addresses included in 172.16.0.0/19 in area 0?
R1(config-router)# network 172.16.0.0 0.0.0.255 area 0
14. A router boots and enters setup mode. What is the reason for this?
The configuration file is missing from NVRAM.
15. When would the network administrator use the ip bandwidth-percent eigrp as-number percent command?
when there is a low bandwidth connection
17. Refer to the exhibit. Routers R1 and R2 are directly connected via their serial interfaces and are both running the EIGRP routing protocol. R1 and R2 can ping the directly connected serial interface of their neighbor, but they cannot form an EIGRP neighbor adjacency.
What action should be taken to solve this problem
Configure both routers with the same EIGRP process ID.
18. Refer to the exhibit. Pings are failing between HostA and HostB. The network administrator discovers that Router1 does not have a route to the 172.16.0.0 network. Assuming Router2 is configured correctly, which two static routes could be configured on Router1 to enable Host A to reach network 172.16.0.0? (Choose two.)
ip route 172.16.0.0 255.255.0.0 S0/0
ip route 172.16.0.0 255.255.0.0 192.168.0.2
19. A static route has been configured on a router. However, the destination network no longer exists. What should an administrator do to remove the static route from the routing table?
Remove the route using the no ip route command.
20. What is the function of the OSPF LSU packet?
used to announce new OSPF information and to reply to certain types of requests
21. Which of the following are required when adding a network to the OSPF routing process configuration? (Choose three.)
network address
wildcard mask
area ID
23. Which two locations can be the source of the Cisco IOS that is used by a router during the bootup process? (Choose two.)
flash memory
NVRAM
25. Refer to the exhibit. Which path will traffic from the 172.16.1.0/24 network take to get to the 10.0.0.0/24 network?
It will load balance the traffic between ADC and ABC
26. Which three statements are true regarding the encapsulation and de-encapsulation of packets when traveling through a router? (Choose three.)
The router modifies the TTL field, decrementing it by one.
The router maintains the same source and destination IP.
The router changes the source physical address to the physical address of the exit interface.
27. Because of a topology change, the next hop IP address in the current static route must be reconfigured. How can a static route entry be altered to accommodate a topology change?
Negate the existing static route and configure a new static route with the correct next hop IP address.
28. Refer to the exhibit. What is the meaning of the highlighted value 120?
It is the metric that is calculated by the routing protocol.
29. A network administrator has configured a default route on Router_A but it is not being shared with adjacent Router_B and the other routers in the OSPF area. Which command will save the administrator the time and trouble of configuring this default route on Router_B and all of the other routers in the OSPF area?
Router_A(config-router)# default-information originate
30. Which routing protocol by default uses bandwidth and delay to calculate the metric of a route?
EIGRP
31. Refer to the exhibit. Which route in the routing table of R1 will be discarded by its neighboring router?
192.168.3.0
32. Refer to the exhibit. What are two of the routes added to the routing table of R1? (Choose two.)
R 192.168.1.0/24 [120/1] via 172.16.2.1, 00:00:24, Serial0/0/1
R 192.168.100.0/24 [120/1] via 172.16.1.1, 00:00:24, Serial0/0/0
33. Refer to the exhibit. A network administrator has run the show interface command. The output of this command is displayed. What is the first step that is required to make this interface operational?
Issue the no shutdown command on the interface.
34. Refer to the exhibit. A device is required to complete the connection between router R1 and the WAN. Which two devices can be used for this? (Choose two.)
a CSU/DSU device
a modem
35. Refer to the exhibit. A network administrator is accessing router R1 from the console port. Once the administrator is connected to the router, which password should the administrator enter at the R1> prompt to access the privileged EXEC mode?
Cisco789
36. Which routing protocol maintains a topology table separate from the routing table?
EIGRP
37. Refer to the exhibit. The network has three connected routers: R1, R2, and R3. The routes of all three routers are displayed. All routers are operational and pings are not blocked on this network.
Which ping will fail?
from R1 to 192.168.3.1
38. Refer to the exhibit. Which two routes are child routes? (Choose two.)
10.0.0.0
10.1.2.0
39. Refer to the exhibit. What information can be determined from the displayed output?
Router R2 is receiving hello packets from a neighbor with the IP address 192.168.10.10 via the R2 S0/0/1 interface.
46. How does route poisoning prevent routing loops?
Failed routes are advertised with a metric of infinity.
Thank Affro!
Hi.
You're doing a great job with all the ccna materials. Thanks for this :)
Could you do me a favour please and post any CCNA2 Final H answers. I'm taking the exam tomorrow and would like to be prepared as much as it's possible.
Thanks in advace,
Regards
Lukas
40. The command ip route 192.168.2.0 255.255.255.0 172.16.2.2 was entered into the router. After network changes were made, the new next hop for the 192.168.2.0/24 network is 172.16.5.1. What should an administrator do so that the router will use the new next hop to reach the 192.168.2.0 network?
Negate the original command and enter a new static route with the new next hop.
41. What does RIP use to reduce convergence time in a larger network?
It uses triggered updates to announce network changes if they happen in between the periodic updates.
42. Refer to the exhibit. Which host has a combination of IP address and subnet mask on the same network as Fa0/0 of Router1?
host B
43. Refer to the exhibit. All interfaces are addressed and functioning correctly. The network administrator runs the tracert command on host A. Which two facts could be responsible for the output of this command? (Choose two.)
The entry for 192.168.1.0/24 is missing from the routing table of R2.
The entry for 192.168.2.0/24 is missing from the routing table of R1.
44. Refer to the exhibit. When troubleshooting a network, it is important to interpret the output of various router commands. On the basis of the exhibit, which three statements are true? (Choose three.)
The missing information for Blank 1 is the command show ip route.
The missing information for Blank 2 is the number 120.
The missing information for Blank 3 is the letter C.
45. Which statement is true about the RIPv1 protocol?
It excludes subnet information from the routing updates.
46. How does route poisoning prevent routing loops?
Failed routes are advertised with a metric of infinity.
47. Refer to the exhibit. The network is running the RIP routing protocol. Network 10.0.0.0 goes down. Which statement is true regarding how the routers in this topology will respond to this event?
Router5 will send Router4 a triggered update with a metric of 16 for network 10.0.0.0.
48. Refer to the exhibit. A network administrator has configured OSPF using the following command: network 192.168.1.32 0.0.0.31 area 0
Which router interface will participate in OSPF?
Serial0/0/0
49. Refer to the exhibit. An administrator is adding a new subnet of 50 hosts to R3. Which subnet address should be used for the new subnet that provides enough addresses while wasting a minimum of addresses?
192.168.1.64/26
50. Refer to exhibit. Given the topology shown in the exhibit, what three commands are needed to configure EIGRP on the Paris router? (Choose three.)
Paris(config)# router eigrp 100
Paris(config-router)# network 192.168.7.0
Paris(config-router)# network 192.168.9.0
51. Refer to the exhibit. OSPF is used for the routing protocol and all interfaces are configured with the correct IP addresses and subnet masks. During testing, it is found that router R1 is unable to form an adjacency with R2. What is the cause of this problem?
Both routers have been configured with different hello and dead intervals.
52. Refer to the exhibit. All routers are configured for OSPF area 0. The network administrator requires that R2 always be the DR and maintain adjacency.
Which two configurations can achieve this? (Choose two.)
Change the priority values of the Fa0/0 interfaces of R1 and R3 to 0.
Configure a loopback interface on R2, with an IP address higher than any IP address on the other routers.
I'm missing the answers for questions: 3, 11, 22 and 24.
I don't know if the answers are correct, but I think the score should be at least 80%.
Thank again!
CCNA2 passed :)
85%
Additions to above:
Missed questions and correcting Q13,23,28,31,38 & 50
3. A static route is established
11.Automatic summarization is enabled on R1
22.The configuration register is not configured with the default setting
24.The last set of digits (11100000) is 224 which are used for multi-casting which is what these 3 protocols use for advertising.
Incorrect answers:
13.R1(config-router)# network 172.16.0.0 0.0.31.255 area 0
Why?:0.0.31.255 is sufficient without adding the whole range.
23.flash memory, TFTP Server
Why?: Look up IOS in the semester search function its shown in a picture!!! (flash and TFTP is where you can boot an IOS from)
28.It is the administrative distance of the routing protocol.
Why?: the first is the AD the second is the metric in this cast 120 is RIPs AD and 1 is the hop count.
31.Its 192.168.4.0
Why? 192.168.3.0 will still be in the neighbor as either a directly connected OR 2 hops(depending on which way you go). 192.168.4.0 will be 14 hops for a closer neighbor or will be 16 ie. infinity and will be dropped by neighbors further away from this route.
38.10.1.2.0,10.2.2.0
Why?: these are both child routes of the parent route 10.0.0.0 and one of the above mentioned routes that is incorrect is the parent route 10.0.0.0
50.Paris(config)# router eigrp 100
Paris(config-router)# network 192.168.7.0
Paris(config-router)# network 192.168.8.0
Why?: These networks are directly connected and need network statements so that routing will be enabled on them. The 192.168.9.0 network is on a different route so it is responsible for that network statement and not this router.
Anything I have gotten wrong please feel free to correct me as I would like to know for my own benefit. And if I have missed any correct answers lucky you for picking them up as the first guy who posted and myself did not pick them up. lol
Have fun with these answers and good luck!
2nd last para should say "it is on a different routerso it is responsible for that network statement..."
After all this most of these question were not even on my test :(
Pity I didn't have more time to look over other exams, Still, did the test today and got over 95% (I don't want to put my actual result unless my teacher looks at this site :p )
@Kamikaze:
:D
when r u gonna Put the Answers in this Site...
thanxxx to AFFRO
you're my savior :P
and for quocvuong, i'll send you my document, 90%pass :)
Which multicast address does EIGRP use to send hello and updates packets?
*224.0.0.5
*224.0.0.6
*224.0.0.9
*224.0.0.10
>>please indicate the answer
Post a Comment
1. Please don't use offensive language.
Such comments will be deleted immediately.
2. Please don't comment anonymously.
Use a nick name or blogger ID in your comment.
Happy Commenting !